Stainless Steel Gear Pump For Vegetable Oil. pump body, pump cover, impeller, etc. All parts contacting with materials according to customer’s requirements by: SS304, SS316, SS316L, SUS304, SUS316, SUS316L and stainless steel.The pump diameter has: 1 inch, 2 inch, 3 inch, 4 inch, 6 inch, 8 inch, 10 inch, 14 inch and so on.
What is vegetable oil?
Vegetable oil is a kind of plant kernel rich in oil. After pretreatment such as cleaning and removing impurities, peeling, crushing, softening, rolling, extrusion, etc., crude oil is extracted by mechanical press or solvent extraction, and then obtained by refining.(Stainless Steel Gear Pump For Vegetable Oil)
Stainless Steel Gear Pump For Vegetable Oil Structure :
With good self – imbibition, so before each pump must not be filled with liquid.
Stainless Steel Gear Pump For Vegetable Oil simple and compact structure, easy to use and maintain.
Lubrication is automatically achieved by the liquid delivered, so there is no need to add additional lubrication fluid in daily work.
The use of elastic coupling to transfer power can compensate for small errors caused by installation.In the oil pump work by the inevitable hydraulic impact, can play a good buffer.
motor adopts the brand of three-phase ac motor, which conforms to the requirements of the European Community “CE” mark;Explosion-proof motor can be used to meet the needs of different occasions.Superior electrical performance, low noise, low vibration, the standard design of the motor protection class IP55, insulation class F.Operating voltage: ≤3Kw, 220-240v / 380-420v, delta /Y, > 3Kw, 380-420v / 660-690v, delta /Y;Frequency: 50Hz/60Hz;Working mode: continuous (SI);Speed: the speed of the standard pump is 1450r/min
Install stainless steel gear pump:
A. Before installation, check whether the pump is damaged in transportation, such as whether the motor is damp, whether the dust cover at the pump inlet and outlet is damaged and whether dirt enters the pump chamber.
B. Clean the inner wall of the pipe with clean water or steam before installing the pipe.Installation should avoid the weight of the pipe to be borne by the pump, so as not to affect the accuracy and life of the pump.
C. The gear oil pump should be as close to the oil pool as possible;No leakage of air or liquid is allowed in the connection parts of the pipeline, or the phenomenon of not absorbing liquid will occur.
D. In order to prevent dirt such as particles and impurities from entering the pump, a metal filter screen should be installed at the suction inlet with a filtration accuracy of 30 mesh /in, and the filtration area should be more than three times larger than the cross-sectional area of the inlet pipe.
E. It is recommended to install vacuum gauge and pressure gauge for inlet and outlet pipeline to monitor the working status of the pump.
F. When the oil pool is deep, the suction pipe is long or the medium viscosity is high and the vacuum degree is too high, the inlet pipe can be thickened.When the suction pipe is longer, the bottom valve should be installed.
Inspection of stainless steel gear pump before working:
A. Whether the fasteners of the pump are firm or not.
B. Whether the rotation of the driving shaft is uniform in weight.
C. Whether the valve in and out of the line is open.
D. Whether the rotation direction of the pump meets the requirements.
E. Proper amount of medium should be injected into the pump before the first use.
Maintenance of stainless steel gear pump during operation:
A. Note that the readings of the pressure gauge and vacuum gauge of the gear oil pump shall be within the specified technical specifications of the pump.
B. When the gear oil pump has abnormal noise or excessive temperature rise during operation, the pump should be stopped immediately for inspection.
C. In general, the safety valve should not be adjusted arbitrarily. If adjustment is needed, the safety valve should be calibrated with an instrument.Make the cut-off pressure of the relief valve a pump
D. 1.5-2 times rated pressure.
Stainless steel gear pump stop
A. turn off the power.
B. Close inlet and outlet valves.