YCB30-0.6 Gear Pump Performance parameters: flow rate: 30~36m3/h;Revolution: 970 ~ 1170 r/min;Head: 60 m;Pressure: 0.6 Mpa.Motor power: 11KW;Motor model: Y160L-6;Temperature: 300℃;Connection: flange.
Structural features of YCB Gear Pump:
YCB30-0.6 gear pump series of gear pump mainly consists of gear, shaft, pump body, pump cover, bearing sleeve, shaft end seal, etc.The gear is made of double arc sinusoidal tooth.Its outstanding advantage compared with involute gear is that there is no relative sliding of the tooth profile in the process of gear engagement, so the tooth surface has no wear, smooth operation, no trapped liquid phenomenon, low noise, long life, high efficiency.The pump got rid of the traditional design constraints, so that the gear pump in the design, production and use into a new field.The pump is equipped with pressure valve as overload protection, the pressure valve full backflow pressure is 1.5 times of the rated discharge pressure of the pump.Can also be in the allowable discharge pressure range according to the actual needs of another adjustment.However, please note that this pressure valve cannot be used as pressure reducing valve for a long time.
If necessary, it can be installed separately on the pipeline.Shaft end seal design for two forms, a mechanical seal, a packing seal, according to the specific use and user requirements.From the shaft overhang end to the pump, for clockwise rotation
Performance parameters of YCB Gear Pump:
|
Model |
Capacity Q |
Speed n |
Pressure p |
(NPSH)r |
Motor |
||
|
m3/h |
Hz |
KW |
Model |
||||
|
YCB8-1.6 |
8.0 |
970 |
1.6 |
7.0 |
50 |
11 |
Y160L-6 |
|
12.0 |
1460 |
50 |
15 |
Y160L-4 |
|||
|
9.6 |
1170 |
60 |
11 |
Y160L-6 |
|||
|
14.4 |
1760 |
60 |
15 |
Y160L-4 |
|||
|
YCB10-0.6 |
10.0 |
960 |
0.6 |
5.0 |
50 |
4 |
Y132M1-6 |
|
15.0 |
1440 |
50 |
5.5 |
Y132S-4 |
|||
|
12.0 |
1170 |
60 |
5.5 |
Y132M2-6 |
|||
|
18.0 |
1750 |
60 |
7.5 |
Y132M-4 |
|||
|
YCB10-1.6 |
10.0 |
970 |
1.6 |
7.0 |
50 |
11 |
Y160L-6 |
|
15.0 |
1470 |
50 |
15 |
Y160L-4 |
|||
|
12.0 |
1170 |
60 |
11 |
Y160L-6 |
|||
|
18.0 |
1770 |
60 |
18.5 |
Y160L-4 |
|||
|
YCB20-0.6 |
20.0 |
970 |
0.6 |
5.0 |
50 |
7.5 |
Y160M-6 |
|
24.0 |
1170 |
60 |
7.5 |
Y160M-6 |
|||
|
YCB25-0.6 |
25.0 |
970 |
0.6 |
5.5 |
50 |
11 |
Y160L-6 |
|
30.0 |
1170 |
60 |
11 |
Y160L-6 |
|||
|
YCB30-0.6 |
30.0 |
970 |
0.6 |
5.5 |
50 |
11 |
Y160L-6 |
|
36.0 |
1170 |
60 |
11 |
Y160L-6 |
|||
|
YCB40-0.6 |
40.0 |
970 |
0.6 |
5.5 |
50 |
15 |
Y180L-6 |
|
48.0 |
1180 |
60 |
15 |
Y180L-6 |
|||
|
YCB50-0.6 |
50.0 |
970 |
0.6 |
5.5 |
50 |
22 |
Y200L2-6 |
|
60.0 |
1180 |
60 |
22 |
Y200L2-6 |
|||
YCB30-0.6 Gear Pump Installation and precautions :
1. Check the ticket for the pump and motor before installation. All parts should be intact and there should be no sundries in the pump.
YCB Gear Pump
2. Connect the pump to inlet, inlet pipe and power supply at the horizontal position.Finally, use the hand disk to move the coupling, check whether there is any rub phenomenon, rotation is easy to weigh, then the installation ends.
3. Plastic alloy pump steel is poor, the weight of the pipe can not be directly pressed on the pump body, the inlet and outlet pipeline should be additional support to bear, the pump with high head should be installed in the outlet reverse check valve, in case of sudden stop of the water hammer damage.
4. All joints must be kept sealed to prevent air leakage and fluid from affecting the working performance of the pump.
5. Stop immediately if any movement or abnormal sound is found in the process of operation, and work can only be done after troubleshooting the ticket checking cause.